feat(hero): v0.1.2 — scale calibration, façade detail, export preset refactor (#28)

Merged PR #28: v0.1.2 — scale calibration, façade detail, export preset

Co-authored-by: Zwitschi <zwitschi82@gmail.com>

TODO.md

@@ -9,18 +9,6 @@ Actionable task list for this project. This file is the single, central place fo
 - When all steps in a version section are done: write a `CHANGELOG.md` entry, then remove the version section from this file.
 - Release gate: a version is tagged only on the owner's explicit go-ahead once its release checks pass, not automatically when the checkboxes close.
 
-## 0.1.2 — Scale and façade corrections (patch)
-
-Suggested blender skills: **references** (reference-image-match and visual-match-checklist templates — measure the guessed heights and colonnade proportions against the photographs), **archviz** (real-world scale and façade composition discipline), **camera-cinematography** (reproduce the reference camera angles when comparing renders to photos).
-
-### Patch tasks - active - 01a1b26b-3c94-707f-9665-2f6b4a79b564 (branch `scale-facade-0.1.2`)
-
-- [x] Correct building scale and street proportions flagged against references. **Mapbox adopted 2026-11-09.** `Geo/tools/mapbox_buildings.py` merges our OSM heights with Mapbox's building data for the same footprints; after adopting its two findings the cross-check reports **66 match, 6 non-building, 0 disagreements**. Adopted: **`LEVEL_HEIGHT` 3.2 → 3.1 m** (`block_height_report.py`, and the Blosm `--level-height` default), plus explicit `HEIGHT_OVERRIDES` (3.0 m) for the three rear `building=yes`/`apartments` structures Mapbox gives as single-storey. Blockout regenerated, frontage re-exported/re-imported, DemoMap rebuilt; packaged `-qaselftest` all PASS. Measured effect: 6922 42.1 → 39.1 m, El Capitan Theatre 20.0 → 20.5 m (both now ~1.9 m above their table height = roof mass).
-- [ ] Refine hero façade details where reference photography shows discrepancies.
-- [x] **Replace the placeholder heights.** **Resolved 2026-11-08 — they were never unknown buildings.** The three "guessed" ways are not building volumes at all: `1360755125` and `1360755126` are `building=roof` at `layer=1` (elevated canopies) and `1417995292` is `amenity=shelter` / `shelter_type=public_transport` (a transit shelter). The report defaulted them to "2 levels × 3.2 m" and produced the bogus 6.4 m. `Geo/tools/block_height_report.py` now classifies roof/shelter explicitly and reports **0 guessed heights**: all 15 block volumes have a real `height` tag, a `building:levels` derivation, or are correctly excluded as non-building volumes. No photograph measurement was needed, and no frontage building was affected.
-- [ ] Resolve the remaining unknown on the hero: the colonnade currently occupies about 45 % of the height against roughly 50–60 % in the photographs. Fix the vertical proportions. **Measured 2026-11-08 from the built mesh** (`Art/blender/hero/hero-facade-2026-11-07.blend`): envelope 0–14.50 m; stylobate 0–2.00; columns 2.00–7.95; capitals 7.95–8.90; entablature 8.90–12.30; parapet 12.30–14.50. So the colonnade (columns + capitals) is **6.90 m = 47.6 %** of the height — inside the range only at the low end. Bringing it to ~55 % needs ~+1.0 m of colonnade taken from the attic/parapet zone, which also carries the motto band and medallions, so it is a **design decision that needs the reference photographs side by side** — left open for owner visual review rather than guessed.
-- [ ] Tag `v0.1.2` and write `CHANGELOG.md` entry; then remove this section.
-
 ## 0.1.3 — Packaging and setup fixes (patch)
 
 Suggested blender skills: **export-pipeline** and **unreal-export** (scale/pivot/normals/materials/collision verification) if any packaging defect traces back to the Blender export presets.